Jiangsu pump truck lubricant manufacturer-how much does a bag of pump lubricant cost?

Contents of this article

• Can the lubricant be poured directly?

• How to use pump lubricant?

• What is the difference between pump mortar and ordinary mortar?

• What does pump mortar mean?

• How to use pump mortar in construction?

• What kind of chemical raw material is the lubricant? Will it harm the pump truck?

Can lubricant be poured directly?

The use of lubricant is very simple, easy to operate, and does not require additional equipment. In order to ensure normal use and reduce concrete quality problems and pipe blockage caused by improper operation, we stipulate the following:

1. For pump trucks with a length of less than 56 meters, use one pack of pump lubricant (pump treasure) each time ( 300g).

2. First add about 30kg of water into the hopper of the concrete pump truck, then pour a pack of pump lubricating agent (300g) into the water. Stir for 1 minute, stop for 3 minutes, and then stir again. Wait for 1 minute to fully dissolve. When the solution becomes thick and lubricated, it can be used.

3. After the concrete tanker arrives at the site and confirms that the project, location, and strength are correct, start slowly unloading concrete from the other side of the pump pipe feed inlet to the hopper. When the concrete covers the transfer pump feed inlet, Pressurized pumping can begin. Try to allow all the lubrication solution to flow at the front end of the concrete pipe, through the pump pipe first, and the concrete is pushed and pumped behind.

4. When using lubricating agent to lubricate the pump, be careful not to pour the solution discharged after lubricating the pump into the concrete structure. The first few strokes of the lubricating pump solution and concrete must be The material is discharged outside the concrete formwork until the concrete does not contain wetting solution. Direct pouring into concrete structures is not allowed to prevent quality accidents.

5. The operation process must be strictly implemented in accordance with regulations. The production department and laboratory will send personnel to the site from time to time to inspect the implementation, which will be evaluated as an important part of the pump efficiency assessment.

It should be noted that when the temperature is very low, the dissolution rate of the lubricating agent may be reduced, and the stirring time should be appropriately extended. We require: stir for 1 minute, stop for 5 minutes, and then stir for 1 minute. minute.

How to use pump lubricant?

How to use concrete pump lubricant: For pump trucks with a length of less than 56 meters, use one pack (300g) of pump lubricant (pump treasure) each time. First add about 30kg of water into the hopper of the concrete pump truck, and then add a pack of pump lubricating agent (300g). After the concrete tanker arrives at the site and confirms that the project, location, and strength are correct, use the pump pipe feed inlet and use the pump lubricating agent. When lubricating the pump, be careful not to pour the solution discharged after the pump into the concrete structure. The lubrication procedures must be strictly followed during the operation.

What is the difference between pump mortar and ordinary mortar?

Difference: The texture is different

The pump mortar fully lubricates the delivery pump piston and the inner wall of the pipeline to form a lubricating film, thereby effectively reducing the flow resistance between the concrete and the pipeline and avoiding the risk of damage to the pipeline. The clogging phenomenon caused by sticky slurry can achieve normal pumping.

Ordinary mortar is a binding material used for bricklaying in buildings. It is made of a certain proportion of sand and cementing materials (cement, lime plaster, clay, etc.) mixed with water. It is also called mortar or mortar.

What does pump mortar mean?

The pump mortar fully lubricates the delivery pump piston and the inner wall of the pipeline to form a lubricating film, thereby effectively

reducing the flow resistance between concrete and pipelines and avoiding problems caused by slurry in the pipelines. blockage phenomenon

to achieve normal pumping.

2. Mix ratio:

The pump mortar is generally used in accordance with the national standard “Technical Regulations for Pumping Concrete Construction” to pump concrete

pump mortar: Cement mortar; Cement mortar with the same mix ratio as concrete, except for coarse aggregate.

How to use pump mortar in construction?

Just go inside and no one will give you 0.7 square meters of merchandise. Just ask for 1 square meter. Do not use mortar for jointing. You can put it in a bucket and use it when building pillars or walls (it is generally necessary to fill in mortar first when building pillars and walls to avoid root rot).

If you are really tight and don’t want to use it, you can use it as a spacer. The ground pump can only be placed in a bucket and dropped with a tower crane.

The above methods are applicable regardless of the season.

What kind of chemical material is the lubricant? Will it harm the pump truck?

What the person above said in this ambiguous way is both harmful and not harmful. Let me tell you, lubricating agent, also known as pumping agent, will not harm the pump truck. Its specific function is to add pumping agent to the water. The pumping agent will turn into a snot-like viscous substance and adhere to the inner wall of the pipe. When pumping concrete, it is Concrete brings out the attached pumping agent</p